Pipes Tips To Make Use Of When Taking On A Task

Plumbing can be very intimidating to someone that has never done it before. It can easily lead to a bit of information overload because of all of the resources available to new plumbers. Below are some tips to assist you in getting all of this information organized to where you can start plumbing correctly.

Rigid copper is used for main water lines in many homes. You cannot bend rigid copper, so joints and tees must be soldered on. When soldering, always apply flux (also called soldering paste) to both surfaces. Flux retards oxidation when the copper is heated. Always use lead-free or nearly lead-free solder when sweating a copper joint.

You should drain all of the water out of the tank of your hot water heater at least once every three to six months. Draining all of the water out of the tank helps to prevent sediment build-up at the bottom of the tank. This sediment can cause the tank to bang or to heat less efficiently.

If you have noisy pipes, you can cushion them with a rubber blanket or add additional anchor straps. Banging pipes are usually caused by loose pipes, water hammering to a stop as you turn it off, or hot water pipes shifting in their position. All of these problems can be solved by cushioning and anchoring the pipes.

When starting a plumbing project that is due to loud noises in your pipes empty the pipes first. This can be an easy fix to an other wise wasted huge job. Just close the main water line and open the facets throughout the house. After the water has stopped flowing turn the water on from the main source and check to see if the noise is eliminated.

Watch how your toilets are flushing. If you have to jiggle the handle or if it takes too long, you might have to repair some toilet parts. Replacing these parts early may help you to save on your water bills and will save you from more expensive repairs at a later date.

If your toilet will not flush, and there is very little water in the basin, try to fix the issue by dumping warm water in the bowl from around your waist line. If the water goes down to a lower level again, then you should repeat the procedure.


Sometimes you have to make the choice between replacing or repairing. If you have an old appliance, that uses a lot of water or electricity, it may be best to replace. Sure, it will cost more initially, but it will save you money in the long run. The other thing is, you can't be sure how well a repair will work out, whereas with a new appliance you'll at least get a guarantee.

Water that drains back into your dishwasher is likely due to an improper sink hook up. The hose from your sink to your dishwasher needs to go upward before going back down so that there is no mixing between fixtures.

If you are experiencing sewage backing up to your toilet, it is often due to blockages contained in the lateral connections connected to the main sewage line. When your personal efforts can't deal with such a clog, your only option is to have the line snaked out by a professional plumber.

Regular maintenance of your plumbing lines is a great idea. visit website are getting your lines snaked or jetted. Jetted is a technology that is proven more effective than snaking is. It gets deeper and cleans harder. So jetting is a good idea next time you are having maintenance performed on your lines.

Call different plumbers before choosing one. Plumbing prices among professionals are not uniform. Before you hire someone to fix a major problem, call two or three other plumbers to see what their prices are like. This can be difficult if you have a major plumbing problem that you need solved right away, but will save you money in the end.

When http://rodger47kermit.blogzet.com/easy-ways-on-how-to-do-pipes-right-6790359 , it is time to disconnect your water hoses from your outside faucets. If you forget to do this, water in the hoses can freeze and expand. This can cause the faucets and the connecting pipes inside your house to freeze and break. By simply rolling up your garden hoses and storing them for the winter, you can help prevent costly plumbing repairs.

Check https://www.domain.com.au/news/in-2018-it-costs-more-to-hire-a-removalist-than-any-other-tradesperson-or-household-service-20180715-h12q5e-752601/ in your home. If your home has the flexible gray polybutylene water pipes, you need to have a plumber come out and assess their condition. These types of pipe are prone to failure and can lead to very costly repairs if they have a failure within your home.

When leaving on vacation or leaving your vacation home, be sure to turn off the main water before you leave. If something happens while you are gone you can cause some serious damage from a flooded basement or a broken pipe in the wall that leaks for weeks until you return.

To make sure your sump pump will run in an emergency, routinely test it by adding several buckets of water into the sump pit. The pump should turn on, remove the water and turn off with ease. Do this regularly, especially if your sump pump doesn't run that often, to ensure it will work when needed most.

If you must call a professional to repair your plumbing problem, be prepared with a list of all of your plumbing problems, no matter how small or trivial. Plumbers typically charge a set fee just to make a house call, usually the price of one hour of their time. But, if they can fix your initial problem in a few minutes, you will get more value for that service call and avoid having to pay for another, by having them check out other issues.

To keep your drains moving freely and free from gunk and buildup, pour a half cup of baking soda followed by a cup of white vinegar down each drain once a month. The foaming action helps to push stuck substances through the pipe, while the vinegar neutralizes odors. straight from the source can follow this solution with a kettle of boiling water for extra cleaning power.

In conclusion, you now know what causes the squeaking noise from your pipes, as well as a lot more information. Use this guide as the best way to take care of any plumbing issues that might come up. Hopefully, you were able to comprehend the advice given and will be able to fully utilize it whenever needed.

Baffled By Plumbing Problems? Get Assist Here!

If plumbing is something that you find difficult or intimidating, you are not alone. Many people can't solve their own plumbing problems, which means that plumbers can charge a lot of money for even simple and quick repairs. Don't let this happen to you, read on to learn how to solve your own plumbing problems!

If you have pipes that sound as if they're squeaking or hammering, it's an easy fix. Anchor exposed pipes to get rid of noises. Pipes that are contained within the floors, walls and ceilings may need to be attended by a professional plumber.

If a pipe ever freezes, you need to make sure to shut off the water. This will keep the pipe from bursting and causing you major damage to your home. Make sure to shut the water off at the main valve, and then open the faucet that is closest to the frozen pipe so it can drain while it is thawing out.

To avoid having your outdoor faucets freeze up in the winter, detach all hoses before the first freeze. Also, close the shutoff valve that leads to the outdoor faucets, then turn on the outdoor faucets to let any remaining water in the lines drain. Once temperatures warm up in the spring, you can reverse the process.

Unclog drains with ease. Try using a plunger and drain cleaner, as your clog may simply be a build-up of hair and debris. If this doesn't work you may have to clear the drain with a snake. Feed the snake into the drain line as far as it will go. Turn the crank gently, which will help to loosen the clog. Remove the snake, and run water down the drain to see if the clog has been removed. You may have to use the snake a couple of times, before the clog is cleared so don't give up!

If your pipes are prone to freezing, let the water trickle continuously in at least one faucet during weather that is below freezing. This will minimize the chances that the pipes will freeze and leave you without water. If websites is continually running through the pipes and trickling out of a faucet, the pipes are less likely to freeze.

By installing water-conserving shower heads in your bathrooms, you can save money on your monthly water bill. Your shower consumes a majority of the hot water usage in your home. When you install an energy-efficient shower head, you will reduce your home's water consumption, which means money left in your pocket.

If your drain in any device is taking longer to drain water, then you may need to have your pipes professionally cleaned depending on the severity of the circumstances. Before you do this, there are several different products you can try. However, some of them are professional strength and all products should be used with caution.

Do not be surprised if a plumber charges you more than you expected. Many customers think that fixing a toilet or other drainage problem should be easy, therefore the price should be low. You must remember that not only does a plumber have to charge for labor, but they have to charge for parts that you need.


Do you have a frozen drainpipe? You can use a garden hose to thaw it out. First of all, remove the trap from the drainpipe and insert the hose until it will not go any further. While lifting up https://globalnews.ca/news/3905609/7-in-demand-trade-jobs-in-canada/ of the hose, pour hot water down it. Keep pouring hot water down the hose until the drainpipe thaws. To save time with cleanup, keep a bucket underneath to catch the water that overflows.

Do not ignore a slow flushing toilet. This is usually a sign that something is wrong. It can also cause backups and overflows. The most common causes of a slow flushing toilet are sediment build up, tank malfunctions, or partial clogs. You should periodically check for these problems.

Ask before the plumber comes out if they charge for the consultation. In order to quote a project, the plumber has to come out to inspect your particular issue. It is standard to charge for the consultation appointment but the prices can vary wildly. Ask upfront so that you aren't surprised by the total.

To make sure your sump pump will run in an emergency, routinely test it by adding several buckets of water into the sump pit. The pump should turn on, remove the water and turn off with ease. Do this regularly, especially if your sump pump doesn't run that often, to ensure it will work when needed most.

Keep an eye on the hoses for your dishwasher and washing machine. These hoses can leak and bulge, which can be a problem. Check them for signs of wear and tear and replace any hoses more than 10 years old. You'll find that these hoses age well, but you have got to make sure they are doing the job they should.

Do not shock yourself! Water and electricity do not mix well! If you are working with both electrical and plumbing issues at the same time, then you must avoid crossing them. Beware! The two together can be deadly! When water and electricity are mixed, the risk of getting a shock can be incredibly high, as well as deadly.




Governmental regulations sometimes prevent plumbers from actively providing maintenance to copper piping. If you have a calcium buildup in your copper piping, you are going to need to take care of this yourself. You have to get rid of all the water and add vinegar which eats away the calcium buildup out of copper pipes.

One of the most inexpensive plumbing issues is a running toilet. Simply by understanding how a toilet actually functions is the first best tool in avoiding a running toilet. If you understand the function of the lever and floater, you will be able to fix any running toilet in no time.

It is imperative as a homeowner that you know exactly where your main water shut-off valve is located and can operate the valve in case of an emergency. The best first step measure for frozen pipes is to stop water from entering your home in the first place. Locate the main water supply valve and turn it on and off on a regular basis to keep it easily operable in an emergency.

Make sure any plumber that you hire can handle the type of job you have. There are many aspects to plumbing and many contractors can do almost all of them, but some are better suited to doing work involved in specific areas. If need a plumber for your septic system, get one that specializes in septic systems.

In conclusion, you want to be sure that you are getting the best information for someone who knows at least a bit about plumbing. Hopefully this article was perfect for you and you learned at least something. Do not hesitate to keep on furthering your knowledge to give you an even better background.

Having Plumbing Issues? Here Are Exceptional Solutions!

Were you aware that you could get something as cheap and easy to install as a rubber blanket for your pipes in order to take care of that banging noise you hear in your house? Use this article for this and more great plumbing tips to help you today!

You need to winter-proof your house. You have to make sure you switch of the master circuit breaker or the shut-off valve before you leave your house. Since one small hole or congested water can quickly freeze and cause pipes to break and expand, you need to drain and open all outdoor and household water lines.


Don't pay the entire plumbing bill upfront; wait until the plumber finishes the plumbing job. Sometimes it is required to put a little money down before the job starts, but don't ever pay the whole amount before you know the task is done correctly. It will make you feel better knowing that your problem has been solved before parting with a large sum of money.

Frozen and bursting pipes from harsh winter weather is a problem that no-one wants, so plan now to winterize your exterior faucets and pipes against freezing conditions. A simple way to accomplish this is to find the exterior water shut-off valve located inside your home (often located in the basement). Turn off the water valve to stop water flow, and then open up the outside faucets to drain out any water that has collected. Be sure to turn off the outside water faucets tightly after the water has drained out. Take in any hoses you may have outside so they don't crack from the cold weather.

Make sure that you disconnect all hoses outside your house when the fall season hits. This is important to reduce the chance of freezing, which can cause damage to the connecting pipes. Disconnect all of your water hoses and store them safely to put your family in the best position for the fall.

There are many ways to unclog a drain. You can try plunging it at first. If that doesn't work try using a chemical agent from the store. Before you go and spend money at the store though, if you have baking soda and some vinegar handy, you can mix those together and pour them in the drain and try to plunge that but if all else fails they have stronger remedies at your local hardware store.

To avoid freezing pipes in the winter, make sure to insulate any exposed pipes in you basement before winter comes. Pay extra attention to pipes near the outside walls. If you have had a problem with any particular pipe freezing in the past, apply some heat tape to insulate those pipes.

One of the things that you can do to maximize the security of your home is to seal all of the cracks in your outdoor faucets. Even a tiny crack can intensify as the season progresses and lead to serious problems down the road. Reduce pop over here and leaks for optimal protection.

To prevent pipe banging when you turn on the water, think about rubber blankets or straps. Instead of assuming the pipes need replaced, consider anchoring them or buffering them. If your pipes are plastic, leave them some room for expansion and contraction. If pipes do not leak but just make noise, eliminate the noise.

To be successful in any plumbing project, make sure you turn the water off before you start unscrewing pipes. This tip might actually sound insulting, but you are probably getting caught up in having the right tools and parts and being dressed right. Double check that there is not a splash waiting for you. Then triple and quadruple check.

Before embarking on a plumbing project, make sure that you're aware of where the shutoff valve for water in your home is, as well as the valves for shutting off individual structures like sinks, toilets, etc. This way, if something goes wrong, you'll be able to stop the water flow.

Many people wonder where the fruit flies are coming from. Each plumbing fixture has a self-sealed reserve that holds about two cups of water. If those pipes are broken or do not seal off, then odors and residue can cause fruit flies. It is recommended before anything to clean your pipes using bleach. If the flies come back, contact a professional.

Work with plumbers that offer flat rates. When a plumber is charging by the hour, they do not have an incentive to get the job done quickly. It is human nature to go just a little bit slower if it'll mean extra money in our pockets. If you cannot find someone who charges per project make sure that you are vigilant in watching the clock and their work.

If the water is not going into your dishwasher, the first thing you should do is shit off the water under the sink. Chances are that you have some kind of blockage, and keeping the water turned on could actually create a bigger problem. To fix the blockage, you may need to call a plumber.

Use a foaming root killer, twice yearly, to remove tree roots that can bring your drains to a standstill. Foaming products fill the entire pipe with chemicals, killing roots that grow from the top of the pipe as well as the part that water flows through. They are more effective than regular root killers for this reason.

When working outside, it is important that you take regular breaks to give yourself some relief from the sun. When you are focused on work while outside, it can be dangerous if you forget about the sun and heat.

Turn off the water at the main valve immediately if you notice water on the floor by your water heater. If you dawdle, the leak could become worse and it will be difficult to prevent major damage from occurring.

Be sure to check on your hot water pipes annually if they are covered with insulation. Sometimes Recommended Online site can have damaged to them or they could be wearing down and you might not even know it, which is why it is crucial that you check their condition often.

Avoid over-tightening water faucet handles. Use only enough pressure to stop the water from flowing and dripping from the faucet. Get More is overkill and will quickly wear out the gaskets and washers inside those handles and cause leaking or the inability to stop the water from coming out of the faucet.

There are times when a plumber's service is necessary. However, related resource site can be addressed easily if you know how. Learning more about how your plumbing works can save you time and money in repairs. Remember these tips, and they could save you a lot of headaches the next time you have a plumbing problem.

Techniques On How To Do Pipes Right

Were you aware that water pressure above 80 psi can actually cause a loud hammering sound to occur in your plumbing system? This can be easily resolved by installing a valve that can adjust the incoming water pressure. For more great expert tips, check out the rest of this article.

Roots from a tree in your back yard can be a real headache when it comes to plumbing. Make sure if you have a big tree or bush or some kind of plant with a big root system, that you ask your plumbing company about root killing agents. You can flush these down your toilet and kill any roots that may be blocking your pipes and save yourself a lot of money by stopping a back up before it happens.

If your pipes bang when you turn on the water, and all the pipes are anchored correctly, you should add some straps or cushion the pipes with a rubber blanket. There may be times when you will need to do both. Make sure that if you have copper pipes, you are not using galvanized straps.

Routinely check your appliance connections and faucets around the house for any kind of obvious leaks or nearby signs of moisture. Not only do even the smallest leaks lead to a large waste of water and money, they also can lead to damage to your home or even the development of harmful molds.

It is not always necessary to call in a plumber when you have a damaged section of pipe in your plumbing. There are repair kits you can buy in your local hardware store which are excellent in repairing leaks. If you have a small leak, you can rub a compound stick over the hole or crack in the pipe to seal it shut. Epoxy paste is also an excellent remedy for a leaking pipes. Make sure you turn off the water and completely dry the pipe before applying the epoxy.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Always keep find out this here . You can do this in many ways. Pour some dish soap in and let the disposal run for a few minutes with some cold water. Be sure to run it regularly, if not, it can cause rust. To eliminate foul odors, grind lemon or other citrus peels. You can clean the walls of the disposal by grinding small fruit pits or egg shells.

Sometimes you have to make the choice between replacing or repairing. If you have an old appliance, that uses a lot of water or electricity, it may be best to replace. Sure, it will cost more initially, but it will save you money in the long run. The other thing is, you can't be sure how well a repair will work out, whereas with a new appliance you'll at least get a guarantee.

Avoid pouring Learn More Here or oil down your kitchen sink drain. Grease and oil can build up in your pipes and cause a backup. Instead, wait for the grease or oil to cool and solidify and either throw it away or see if there's a place to recycle it near your home.

Call different plumbers before choosing one. Plumbing prices among professionals are not uniform. Before you hire someone to fix a major problem, call two or three other plumbers to see what their prices are like. Gas Pipes Repair can be difficult if you have a major plumbing problem that you need solved right away, but will save you money in the end.

During the winter months, your water heater works the hardest. To keep it in optimum condition, flush it out before winter arrives. Flushing the system helps remove the sediment buildup, which causes internal corrosion of your water heater, shortens its lifespan, and reduces heating efficiency. Connect a hose to the faucet near the bottom of the tank and drain several gallons by directing the water into a nearby drain.

During the week, hair and soap can build up in your drains and can cause serious clogs. Make sure that you have strainers in each of your drains to help catch this debris so that it does not become an issue. This will help to keep your water flowing efficiently.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.


Whenever you work outdoors for a prolonged period of time, take a break in a place where you will not be exposed to the sun. When you are focused on work while outside, it can be dangerous if you forget about the sun and heat.

If you have an ice maker or other plumbing going to your refrigerator, every six months or so pull the refrigerator away from the wall and inspect this plumbing. There should be no condensation or corrosion on these plumbing lines, if there is, contact a plumber and have them look at it.

If you think you understand what is wrong with your toilet, but aren't sure, you should first do some more research on the internet. Most plumbing problems are fairly standard, and you should be able to read about the problem in great detail on several amateur plumber forums to make sure you understand the problem.

Clean washing machine lint traps and use pantyhose over the water outlet tube to prevent lint, fuzz and other debris from clogging sewer or septic system filters. Fine mesh traps are also available for this purpose, but a package of knee-high nylon stockings and plastic ties can provide enough filters to encourage you to do the job regularly.

You should try using a plumbing snake or plumber to unclog a clog. Liquid cleaners that are meant to unclog the clogs in a drain could ruin the pipes. You should also use strainers to catch hair so that it doesn't go down the drain and get clumped and clog your drain.

Before your plumber begins work in your home, make sure you receive a detailed estimate detailing the work to be done, parts needed, a time line and projected completion date. Having all of this information beforehand will give you an idea of what the costs are going to be and how long everything should take.

In conclusion, you want to be sure that you know what all of the noises you hear coming from your basement are. https://search.google.com/local/posts?q=Rocket+Plumbing&ludocid=4600287212252729954#lkt=LocalPoiPosts&lpstate=pid:2601350293752509688&trex=m_t:lcl_akp,rc_f:nav,rc_ludocids:4600287212252729954 could be normal, some could mean that are more serious problems. Hopefully this article will help you determine what sorts of issues require your immediate response.

You Will Not Require To Work With A Plumbing Thanks To These Easy Idea

Welcome to the wide world of plumbing. Plumbing involves a variety of specialized techniques, knowledge and equipment. Plumbing is a personal issue when dealing with home improvement, oftentimes making it seem somewhat difficult to find a solution that works for you. The following hints and tips are designed to provide you with some of the information that you need to get started on developing your plumbing skills and knowledge.

Don't be afraid to call a professional. Don't take on jobs to save money, if you aren't sure how to fix them. Calling a professional plumber saves you money, the experience and know-how can fix your problem sooner and with less fuss.

Before starting any plumbing project on your own be sure to do a great deal of research. There are many resources available to assist you in understanding your plumbing system and help you to avoid many common mistakes made by do-it-yourself novices. Reading about other people's mistakes can make the difference of saving or losing money.

Got a leaky pipe? In many cases you can repair this yourself without the expense of a plumber. If a joint is leaking, tighten it with a pipe wrench. If the leak is coming from a damaged section of pipe, you can try repairing with a store-bought patching kit. One method involves applying waterproof tape to the section of pipe where there is leakage. Before applying the tape, make sure the pipe is thoroughly dry. Make sure that the tape covers two to three inches on either side of the breakage in the pipe.

Don't start any do-it-yourself plumbing project without having a plan in place. You need to know beforehand exactly what you are getting yourself into. Know what kind of space you are working with and what lines are which. Getting a clear picture early on will make your plumbing project go a lot smoother!

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing the damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove Sewer Drain Clog Prevention from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

Periodically check your pipes for leaks and cracks. These can be forgotten, since pipes are usually hidden away, but checking for leaks and cracks can help you identify a small problem before a big problem occurs. You may have to enlist the help of a family member to turn on and off the water stream as you are checking.

Try to limit the amount of hair that goes down your drains. Hair can become tangled up in the pipe and end up blocking up the them, preventing water from flowing smoothly. Buy a cheap screened drain cover to put over your drain to stop any hair from going down and clean it off regularly.

You can remove unsightly mineral buildup from your shower head by soaking it in vinegar overnight. This loosens the deposits, and in the morning you only need to wipe off the residue with a rag. If your shower head is high up an not removable, place vinegar in a plastic bag, slip the bag over the shower head and hold in place with a twist tie.

Before it gets cold, you want to make certain your outside faucets aren't dripping or leaking. If they are, you will need to make the necessary repairs before the freezing temperatures arrive. Freezing water can and will crack pipes, whether they are made of copper, steel, or plastic. Even a hairline crack can make enough water leak to cause a major flood in your home.

During the week, hair and soap can build up in your drains and can cause serious clogs. Make sure that you have strainers in each of your drains to help catch this debris so that it does not become an issue. visit the following webpage will help to keep your water flowing efficiently.

When getting an estimate from a contractor on a job, make sure to ask how long the written estimate is good for. For big jobs you usually want to get estimates from a few different plumbers. Knowing how long your estimate is valid will help you know what your time limit is for making a decision on who to hire.

Keep a grease vat in your kitchen to pour all used cooking grease into. Grease is a big reason that kitchen drains slow and eventually, stop up. Even the harshest drain cleaning products, tend to not be a match for a heavy grease clog. The grease you save in the vat can be formed into balls and rolled in bird seed for wonderful winter bird feeders.

If you install a new water heater, and you start to have a leak from the pressure relief valve, you may need an expansion tank installed. The pressure increases when the functioning of the water heater is being performed properly. Therefore, with your new water heater, it may be necessary to have an expansion tank as well.


The water heater in your home needs to have regular flushing to its plumbing in order to work properly. There is usually Cleaning Drains Services at the bottom of the water heater that a hose can be attached to. Connect a hose to this valve and open it up all the way to flush scale and deposits out of the system.

To avoid plumbing disasters in your kitchen, never place hard-to-grind, stringy, fibrous waste, such as poultry skins, banana peels, carrots, celery, or cantaloupe pulp, into the garbage disposer. The disposer can't sufficiently grind these food products and they will clog your sink drain. You should also run cold water down the drain for about 15 seconds before and after using the garbage disposer to flush the waste down the main drain.

If your sewer and main lines keep clogging up, then it is very possible that you have a tree root blockage problem. There are over https://www.ktnv.com/morning-blend/eternal-plumbing-solutions-llc-10_11_18 can buy to attempt to get rid of this problem. This is very effective, yet the problem is usually very extensive. Therefore, it may require a professional to come out and solve the problem completely.

It is imperative as a homeowner that you know exactly where your main water shut-off valve is located and can operate the valve in case of an emergency. The best first step measure for frozen pipes is to stop water from entering your home in the first place. Locate the main water supply valve and turn it on and off on a regular basis to keep it easily operable in an emergency.

Learn about the subject before you have a problem. Routine maintenance on your home plumbing can prevent future problems from arising. If you follow these tips, you can be ready to fix anything else that goes wrong with your plumbing.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15